Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Las Vegas?
Gate parts and welding in Las Vegas typically run between $150 and $2,800 depending on what broke, what needs fabricating, and whether the gate is manual or motorized. Simple hinge replacements and small crack welds sit at the low end; full wrought-iron section rebuilds or custom gate frame fabrication land at the top. Most Las Vegas homeowners pay between $350 and $1,200 for a typical repair that combines parts and on-site welding.
That range covers the reality of Las Vegas gate work: powder-coated steel that’s been baking in 110-degree sun for a decade, hinges ground down by wind-blown sand, and welds that finally gave way after years of thermal expansion and contraction. At Portcullis Gate Repair Las Vegas, we write the price down before any work starts, so you’ll know exactly where your repair falls in that range before a single weld is struck.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what we’re seeing across Las Vegas neighborhoods in 2026, from Summerlin to Henderson to the older gated communities in the northwest. These ranges include parts and labor. If a tech has to cut out a section and fabricate a replacement on-site, the labor share goes up; if it’s a straightforward part swap with the old bracket still sound, you’ll land at the lower end.
| Repair or Fabrication Item | Typical Las Vegas Price Range |
|---|---|
| Hinge replacement (pair, standard swing gate) | $150 – $450 |
| Single crack weld (no new material) | $120 – $300 |
| Weld repair with steel reinforcement plate | $225 – $550 |
| Replace bent or rusted gate picket (per picket) | $60 – $140 |
| Gate frame corner repair (cut, square, re-weld) | $300 – $750 |
| Custom steel gate frame fabrication (standard 12 – 14 ft drive gate) | $1,400 – $2,800 |
| Latch and catch replacement (mechanical) | $125 – $325 |
| Weld-on receiver bracket for electric gate lock | $180 – $420 |
| Gate truck or roller replacement (sliding gates) | $200 – $600 |
| Post-to-gate alignment repair (cut, shim, re-weld hinge mounts) | $350 – $800 |
What drives cost up or down? The biggest variable is material condition. A gate with thick, clean steel welds quickly. One that’s rusted through at the joints requires cutting back to solid metal before any new weld will hold, which takes time and consumables. The second variable is access: if a welder can work from the driveway with a standard 220V outlet or a mobile rig, that’s straightforward. If the gate is set into a block wall with no room to maneuver, expect to pay on the higher side of these ranges. And the third is finish work: raw welds need grinding, priming, and paint or powder coat touch-up, or Las Vegas sun and hard water will corrode the joint within a season.
What Affects Gate Parts & Welding Pricing in Las Vegas
- Material type and thickness. Wrought iron and ornamental steel fence gates weld cleanly. Thin-walled aluminum requires a TIG welder and a steadier hand, which runs a premium. Some Las Vegas gates are a mix of both, and the tech needs to know which is which before striking an arc.
- Rust and corrosion damage. Las Vegas isn’t Phoenix. We get real monsoon humidity in July and August, and hard-water irrigation overspray eats gate bottoms all year. A gate that looks fine from the street may be paper-thin at the base, and that means more cut-out and more new material.
- Hinge and post condition. Welding a cracked picket is one thing. If the hinges are worn oval or the post has shifted in the ground, the gate will sag and re-crack within months. Old Las Vegas neighborhoods like Paradise Palms and McNeil have 30-year-old gates where post work is the actual repair.
- Gate weight and motor interaction. Electric gates with LiftMaster, FAAC, or BFT operators weigh more than manual gates and shift every time the operator cycles. Welds near the actuator mount or the hinge line bear real stress, so repairs there need reinforcement plates, not just a bead.
- Finish requirements. A raw repair that’s ground smooth and painted to match costs more than a functional weld left as-is. Most Las Vegas HOAs require the gate to be painted to match within 30 days, so the finish work is usually not optional.
- Access and clearance. Gates set tight against block walls, in narrow side yards, or behind landscaping crews have limited room for a welder, grinder, and clamps. If we have to remove the gate leaf and lay it out on the driveway to do the job safely, that labor shows up in the written price.
How to Save on Gate Parts & Welding
Saving money on gate welding isn’t about finding the cheapest welder on Craigslist. It’s about catching damage before it compounds. A $180 hinge replacement in March costs less than a $900 frame rebuild in October, after six months of sagging has pulled the top hinge loose and cracked the adjacent pickets. Walk your gate monthly. Look at the hinge pins, the weld beads, and the bottom rail. If you see orange rust staining, hairline cracks, or a gate that’s starting to drag, call before it worsens.
Another real saver: combine work. If we’re out to weld a cracked corner, adding a hinge replacement or a latch adjustment at the same visit costs far less than scheduling a second trip. The truck roll, setup, and teardown are already paid for. Portcullis Gate Repair Las Vegas gives a written price before any work starts, so you’ll see the combined number and can decide with a clear head. Estimates are free. Call (725) 777-5391 and we’ll give you a real range for your specific gate, not a vague “it depends.”
How Our Gate Parts & Welding Process Works
Here’s the step-by-step, the Kingswell Way. Every Portcullis location is independently owned and operated, but held to the identical four-point Kingswell Guarantee: written price, real arrival window, clean job site, written guarantee on the repair.
- You call, a person answers. No voicemail tree. A live person picks up 24 hours a day, 7 days a week, including holidays. You describe the gate: manual or electric, swing or slide, what’s wrong, and where the gate is in Las Vegas.
- We schedule a real arrival window. Not “sometime between 8 and 5.” You get a window we commit to. Our techs are background-checked and arrive in uniform, and you’ll know who’s coming.
- On-site inspection and written quote. The technician examines the gate, identifies the exact failure, and writes the price down before touching a bolt. You see the number in writing. You decide yes or no.
- Parts and welding done on-site. Most repairs are completed same-day from our truck stock: hinges, brackets, reinforcement plates, latch hardware, and portable welding equipment. For custom fabrication, we’ll cut, fit, and weld on-site or in our shop depending on the gate’s size and finish requirements.
- Cleanup and written guarantee. We grind spatter, sweep the work area, and leave your driveway cleaner than we found it. Then we hand you the invoice with the Kingswell Guarantee stamped on it: 365 days, in writing. If the repair fails inside that period, we come back and fix it at no charge under the 365-Day Done Right Promise.
On the operator side, our technicians carry certified service experience across nine gate-operator brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your gate has a motor on it, the tech arriving already knows that specific system. More on our Gate Parts & Welding in Las Vegas service page.
Common Las Vegas Gate Welding Repairs (and What They Cost)
Hinge Replacement and Re-Welding
Gate hinges in Las Vegas take a beating. Wind gusts off the Spring Mountains flex a gate leaf dozens of times an hour, and the hinge pin is the pivot point for that stress. A standard pair of weld-on barrel hinges runs $150 to $450 installed. That includes cutting off the old hinges, grinding the post face clean, welding the new pair in place, and repositioning the gate to sit square. If the post itself has moved, add $200 to $400 for post reset and re-anchoring.
Cracked Weld Repair on the Gate Frame
We see this most on older wrought-iron gates in the older Las Vegas neighborhoods, where welds from the original install are now 20 or 30 years old. A single crack repair runs $120 to $300. That covers grinding out the cracked bead, cleaning the joint, re-welding, and blending the repair so it doesn’t look like a scar. If the frame metal around the crack is too thin, we add a reinforcement plate: $225 to $550 total. Plates are welded to bridge the weak section, painted to match, and the finish work is included in that range.
Gate Sag and Realignment Welding
A gate that drags on the concrete isn’t just annoying; it’s slowly tearing itself apart. The repair usually means cutting the hinge-side frame, squaring the gate leaf, and welding on a gusset or support wedge to hold the corner at true 90 degrees. In Las Vegas’s North Las Vegas and Centennial Hills areas, where lot gates are long single-leaf swings, this repair runs $350 to $800. The range depends on whether we can do the work with the gate hung or whether we need to lay it flat and clamp it.
Picket and Rail Replacement Welding
Bottom rails and low pickets go first, especially where irrigation overspray keeps the steel damp. Replacing a single picket is $60 to $140. Replacing a bottom rail section that’s rusted through can run $200 to $450, because the rail spans the gate’s width and we have to cut out the bad section, fit a new rail piece, and weld both ends plus re-attach every picket along the span. We use the same gauge steel as the original wherever possible, so the gate doesn’t end up with a patchwork feel.
Electric Gate Lock and Receiver Welding
A Maglock or solenoid lock that’s pulling off the post usually needs a new weld-on bracket. The bracket itself runs $180 to $420 installed, depending on whether we’re fabricating a custom mount or installing a factory bracket for your operator brand. This is a common repair on gates with LiftMaster and DoorKing operators in Las Vegas’s gated subdivisions, where gate lock failures leave a security gap at the post.
Custom Gate Frame Fabrication
When the gate frame is too far gone to repair piecemeal, we fabricate a new one. For a standard residential driveway gate in Las Vegas, 12 to 14 feet across and 5 to 6 feet tall, a custom steel frame runs $1,400 to $2,800. That includes cutting, squaring, welding the perimeter frame, adding hinge and latch plates, and delivering it ready for hang and finish. We’ll match the existing picket spacing and style where possible, so the new frame fits the character of the original gate.
Gate Parts & Welding Safety
Welding a gate involves live electrical current, a molten metal pool at several thousand degrees, and heavy sections that can shift unexpectedly. It’s not a repair to attempt with a weekend hobby welder. A bad weld on a 300-pound gate can fail without warning, and a falling gate leaf is dangerous. Same story for electric gate operators: capacitors inside the control board hold charge even after the breaker is off, and a wrong wire can destroy the operator or cause the gate to move unexpectedly. If your gate needs welding or the hinge line is compromised, we recommend a trained professional. Portcullis Gate Repair Las Vegas techs are background-checked, uniformed, and trained on exactly this work. That’s part of the Kingswell Guarantee: the work is done right, and if it isn’t, we come back. Free of charge.
FAQs – Gate Parts & Welding Cost
How much does it cost to weld a gate in Las Vegas?
A standard gate welding repair in Las Vegas runs between $120 and $550 depending on the crack’s size, location, and whether reinforcement plate is needed. A simple single-crack weld starts around $120 to $300; adding a steel reinforcement plate pushes it to $225 to $550. Call (725) 777-5391 with a description of the gate and we’ll give you a written range before you commit.
Is it cheaper to repair or replace a gate?
For most Las Vegas gates, repair is cheaper until the frame is rusted through in more than two places or the gate is badly bent. A repair typically runs $150 to $800; a new gate frame runs $1,400 and up. The breakeven is usually when repair costs exceed about 60% of replacement cost, but the real answer is to inspect the gate’s steel before deciding. We’ll show you what’s there and let you decide with the numbers in writing.
Can you weld a gate without removing it?
Yes, most gate welding is done with the gate hung in place. Only severe frame distortion or rusted-out bottom rails require laying the gate flat. In-place welding keeps the labor lower, which is why a standard hinge or crack repair in Las Vegas stays in the $150 to $550 range.
How long does a welded gate repair last?
A proper weld on clean steel, finished with paint or powder-coat touch-up, lasts 10 to 20 years in Las Vegas’s dry climate, provided the gate isn’t repeatedly flexing from a separate problem like worn hinges or a failing operator. That’s why we inspect the whole gate, not just the visible crack. And every repair carries the 365-Day Done Right Promise: if the weld fails within a year, we come back and fix it at no charge.
Do you work on electric gates?
Yes. We service nine major gate-operator brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. A weld near the operator mount has to account for the motor’s force, and our techs know the specific system on your property before the truck pulls in. Call (725) 777-5391 for a free estimate on electric gate welding or parts.
Get Your Gate Welding Price in Writing
If you’re in Las Vegas, Henderson, North Las Vegas, Summerlin, or anywhere else in Clark County, and your gate is cracked, sagging, or rusted through, call us. Portcullis Gate Repair Las Vegas is an independently owned Kingswell company serving Las Vegas since 2008. We answer the phone with a live person, 24/7. We arrive in the window we gave you. We put the price in writing before any work starts. And we stamp a 365-day guarantee on every repair invoice. If it fails, we come back. No charge, no argument.
Call (725) 777-5391 for a free estimate, or visit our home page to learn more about how we work.
Written by Dean Prescott, Owner at Portcullis Gate Repair Las Vegas, serving Las Vegas since 2008.
Pricing reflects the Las Vegas market as of 2026. Portcullis Gate Repair Las Vegas offers free estimates – call (725) 777-5391.
What Our Customers Say
"Electric gate kept doing its own thing, opening at random. The tech found a shorted sensor and a worn board, fixed both, and showed me the old parts. Price was what he quoted on the phone."
- Cassandra Pike"Installed a new gate for us after the old wooden one rotted out. Clean work, showed up on time both days, and the written price didn't change. It swings perfectly."
- Donna Kirkpatrick"Gate was dragging and screeching across the driveway. I figured I'd need a whole new setup. He adjusted the track and rollers and it was a fraction of what I expected. Honest work."
- Omar Haddad