Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Las Vegas Homeowners
A gate installation in Las Vegas means more than a fence panel on hinges. It’s a moving piece of equipment that has to hold up to 110-degree summers, fine desert dust that works its way into every moving part, and neighborhoods where a sagging gate is an open invitation. We’ve been installing gates across the Las Vegas valley since 2008, which means we’ve seen what the Mojave climate does to cheap welds and under-spec’d motors. Dean Prescott and the crew at Portcullis Gate Repair Las Vegas run every installation the same way: a written price before the first bolt comes off the truck, a real arrival window, a clean job site, and a 365-day written guarantee on the work. If you’re planning a new gate or replacing one that’s given up, call us at (725) 777-5391 for a free estimate.
Key Takeaways
- Full gate installation in Las Vegas typically runs $2,800 to $7,500 depending on gate type, motor, and site conditions.
- Every project gets a written price before any work begins, plus our 365-Day Done Right Promise.
- We install swing gates, slide gates, and gate openers with service coverage across the entire Las Vegas valley.
- Calls are answered by a live person 24/7, including weekends and holidays.
Automatic Gate Installation
Automatic Gate Installation replaces a manual gate you push open by hand with a motorized system that opens from your car, a keypad, or a phone app. Most homeowners in Las Vegas make the switch because they’re tired of getting out of the car at 9 p.m. in a Spring Valley driveway, or because an HOA in Summerlin or Green Valley asked for a specific entry configuration. We handle the full scope: the gate frame, the opener unit, the safety sensors, the wiring, and the control board programming. For a typical single-leaf swing gate with a new BFT or Linear opener, most Las Vegas jobs land between $3,200 and $6,000 parts and labor. We’ll quote the exact number before anything is ordered.
Swing Gates With Motor Packages
Swing gates are the most common automatic setup for Las Vegas driveways. The gate hinges at one end and the actuator, the motorized arm that physically pushes the gate open, mounts to a concrete or steel post. We set the open and close force on site so the gate doesn’t slam in a wind gust off the Spring Mountains.
Keypad and Intercom Integration
Most automatic gate installations in Las Vegas include some form of entry control: a weatherproof keypad, a car-based remote, or a gate intercom tied to your phone. We wire and program these during the install so you’re not calling back a week later to figure out why the guest code doesn’t work.
Styles & brands we work with
Gate Installation Services
Gate Installation in Las Vegas covers everything from the first site walk to the final programming of the opener. What we actually do in Las Vegas ranges from putting a new gate frame on an existing post to a full ground-up build: posts set in concrete, gate fabricated to spec, opener mounted, safety edges installed, and the whole system tested under load. A standard residential driveway gate with opener and two remotes typically runs $3,800 to $6,500 in Las Vegas. The price swings with gate size, whether we need a new post foundation, and how much electrical work the site requires. We’ll give you the number in writing before the work starts, and that number doesn’t change mid-job.
Full Site Assessment and Measurement
Before any quote, we measure the actual driveway opening, check the grade, look at what’s underground, and note where the power comes in. In neighborhoods like Anthem and Green Valley, HOA setbacks and rock retaining walls change the install path more often than people expect.
Post Setting and Structural Prep
A Las Vegas gate post set in under-compacted soil will lean within two summers. We dig to the depth the gate weight demands, use rebar and proper concrete, and let it cure correctly. That’s the part of the job nobody sees and the part that keeps the gate plumb for years.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Electric Gate Installation
Electric Gate Installation refers to the powered side of the job: the motor, the control board, the wiring, and the safety mechanisms that make a gate move on its own. Some Las Vegas customers already have a perfectly good gate frame and only need the electric system added. Others want the whole build including the electrical run from the house or garage panel. Adding an electric opener with a Ghost Controls or Viking unit to an existing gate frame usually runs $1,800 to $3,400 in Las Vegas, depending on the distance from the power source and whether a permit inspection is required. We’ll pull the right wire, set the limits and force, and leave you with a gate that won’t crush a car or a person.
Safety Edges and Photo Eye Sensors
Every electric gate we install in Las Vegas gets UL-listed safety sensors. That means a photo eye across the gate path and a pressure-sensitive edge on the leading gate panel. If the gate meets a child, a dog, or a bumper, it reverses instead of pushing through.
Power Runs From the Panel
Running 120-volt power from the side of the house to a gate post 70 feet away is standard for us. We bury the conduit to code, use the right gauge for the distance, and label everything at both ends so the next technician, ours or anyone else’s, can see exactly what’s what.
Driveway Gate Installation
Driveway Gate Installation is the most common project we do in Las Vegas: a custom or semi-custom gate across the main vehicle entrance to a home. The gate usually needs to be wide enough for a raised truck or an SUV, strong enough to survive the wind that whips through Sunrise Manor in the spring, and quiet enough not to wake the neighbors when it opens at 6 a.m. A standard Las Vegas driveway gate, either slide or swing, with a BFT or Ghost Controls opener, runs $3,500 to $7,500 installed. The biggest cost variables are gate width, whether it’s a single or double leaf, and whether we’re working with iron, steel, or aluminum frame material. We’ll price all three options.
Double-Drive Gates for Wider Entries
Double-leaf driveway gates split in the middle and swing outward or inward. They work for driveways that are too wide for a single panel, but the two panels have to be hung and synced precisely or they bind in the middle. We adjust the hinge pins and the opener arms so both leaves close tight every time.
Material Choices for the Mojave Climate
Steel holds up better than aluminum against Las Vegas UV and the occasional dust storm, but it needs a proper powder coat or it rusts at the welds inside two or three years. We talk through the trade-offs on every driveway gate quote so you buy the material once and don’t repaint every fall.
Sliding Gate Installation
Sliding Gate Installation means a gate panel that moves sideways on a track and roller system instead of swinging on hinges. In Las Vegas, this style is common on driveways with a steep grade, a short setback from the sidewalk, or not enough room for a swing leaf to arc open. A single sliding gate with opener and track, installed in a typical Las Vegas driveway, runs $4,000 to $8,000 depending on the track length, the gate material, and whether we need to pour a new concrete track bed. Sliders are often the smarter choice for Las Vegas lots where the driveway tilts toward the street, because a swing gate would drag or bind on the pitch. We install cantilever and track-style sliding gates, and we’ll explain which one makes sense for your site.
Cantilever vs. Track Systems
A cantilever sliding gate rides on rollers without a track across the driveway opening, which means no groove in the concrete collecting rocks and dust. In Las Vegas, where landscaping gravel follows every set of tires, that matters. The tradeoff is the gate needs more material to stay rigid, which affects the price.
Track Beds for Sliding Gate Installation
For track-style sliders, we pour a reinforced concrete bed with an embedded steel track set to the right grade. If the track is out of level by a fraction of an inch, the gate drags and wears the rollers out early. We don’t let that happen.
Gate Opener Installation
Gate Opener Installation is the mechanical heart of an automatic gate: the motor, the arm or gear, the control board, and the remotes and keypads. You need this service when a gate is already built but never had an opener, when the old opener is past its useful life, or when a home sale requires a functioning automated entry. For a single-family Las Vegas home, a gate opener installation with a BFT, Linear, or Viking unit runs $1,800 to $3,400 including wiring, programming, and two remotes. The opener is where cheap installs fail, and in Las Vegas heat the control board and capacitor are the parts that cook first. We install units rated for outdoor desert use and we set the safety parameters on site.
Actuator Mounting and Calibration
The actuator, the motorized arm that pushes the gate, has to be mounted on a solid base plate with the hinge geometry set correctly. We drill and tap the posts, bolt everything tight, and set the open and close limits so the motor isn’t straining against the mechanical stops every cycle.
Remote and Keypad Programming
We program the remotes, the keypad entry codes, and any phone app access before we leave. If you want a dedicated visitor code for the gardener or a different one for the house cleaner, we’ll set those up during the install and test each one at the gate.
Gate Fabrication
Gate Fabrication is building the actual gate panel itself, from raw steel or aluminum, to the dimensions of your specific opening. Some Las Vegas homeowners want a standard size off the shelf, but most are better served by a panel fabricated to fit the exact width and height of their existing posts, especially in older neighborhoods like Winchester or Whitney where post spacing was never standardized. Custom fabricated steel gates in Las Vegas run $1,500 to $4,500 for the panel alone, depending on size, design complexity, and whether you choose square tube, picket, or a full privacy panel. We work with local fabricators and weld and finish in-house where the job calls for it. The panel is cut, welded, ground, primed, and powder coated, then hung on the posts and adjusted for clearance.
Custom Sizing for Unusual Openings
If your driveway opening is 11 feet 7 inches, a stock 12-foot gate doesn’t just drop in. We measure to the inch, build the gate for the actual opening, and leave proper clearance at the bottom for grade changes. In Las Vegas, the bottom gap also has to account for the occasional monsoon washout that shifts gravel and soil.
Finish Work and Corrosion Resistance
Steel gates in Las Vegas need a finish that doesn’t bake off in the sun or chip at the weld seams. We use a multi-stage powder coat on steel and recommend it on aluminum too. A properly finished gate panel in this climate should go years, not months, before it needs a touch-up.
Brands We Service
We’re factory-trained on nine major gate opener brands, but we see more BFT, Linear, Viking, and Ghost Controls units in Las Vegas than anything else. With BFT, we’ve done dozens of installations using their hydraulic and electromechanical swing operators, and we stock the common replacement parts like control boards and limit switches so a repair doesn’t turn into a two-week wait. Ghost Controls is popular with Las Vegas homeowners who want a DIY-friendly opener that still meets our install standards, and we’ve learned the specific weaknesses in their battery-backed units under desert heat. Linear and Viking gear shows up on a lot of HOA gates in Summerlin South and Green Valley, and we carry the right diagnostic tools to speak to their control boards directly.
Whether your gate has a Viking operator, a BFT board, or something we haven’t named, we can install, program, and service it. The brand doesn’t change the process: written price first, clean install, written guarantee after.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate sags and drags on the ground. A gate that scrapes the driveway is putting stress on the hinges and the opener motor. Left alone, it burns out the unit or tears the hinge mount out of the post.
- The opener runs but the gate doesn’t move. That’s usually a broken chain, a stripped gear, or a failed actuator arm. Running the motor while the gate is jammed can destroy the control board, which is a much more expensive fix.
- The gate reverses on its own halfway through the cycle. That points to a misaligned safety sensor or excessive force settings. It means the gate is trying to protect you, but it also means someone has to fix the sensor alignment so the gate works reliably.
- The keypad or remote stopped working after a storm. Las Vegas monsoon season puts a lot of moisture into connectors and boards. Water intrusion in a control box left open will corrode the terminals fast.
- The gate post is leaning or the welds are cracked. A leaning post means the foundation under the post has failed. Weld cracks mean the gate is moving under stress it wasn’t built for. Either way, the failure is structural, and a broken gate panel can injure someone.
Safety note: gate springs, counterweights, and the opener mechanism itself are all under tension or load. If you see any of these warning signs, don’t try to disassemble a loaded hinge or a spring-assisted gate yourself. Call a trained technician. The parts that hold a gate up are the parts that hurt people when they let go.
Our Process, Step by Step
- 1
Site walk and measurement. We come to the property, measure the opening, check the grade, look at the existing posts and power, and take note of any HOA or city requirements. Then we walk you through gate type, material, opener brand, and access control options, and we explain the tradeoffs in plain language.
- 2
Written quote, signed before any work. You get a line-item price in writing: gate panel, posts, opener, wiring, controls, and labor. The price you sign is the price you pay. No upcharge at the door, no surprise add-on after the old gate is off the hinges.
- 3
Fabrication or ordering. We build the gate panel to the measurements we took, or order the stock unit that matches. We order the opener and all components from known suppliers we’ve used for years, not whatever’s cheap this week.
- 4
Install day with a real arrival window. You get a time window, and our background-checked, uniformed technician shows up in it. We set posts in concrete, hang the gate, mount the opener, run the wiring, program the controls, and test every safety and access function before we call it done.
- 5
Walkthrough and written guarantee. We show you how the gate works, hand over the remotes and keypad codes, and give you the written 365-Day Done Right Promise on the invoice. If something fails within that year, we come back and fix it at no charge.
How Much Does Gate Installation Cost in Las Vegas?
Here’s what Gate Installation pricing looks like in Las Vegas, broken down by project type. A basic gate opener addition to an existing manual gate runs $1,800 to $3,400. A full automatic swing gate installation with a new panel, posts, opener, and controls runs $3,200 to $6,500. A full sliding gate installation with track, opener, and panel runs $4,000 to $8,000. A custom fabricated steel gate panel alone, before the opener, runs $1,500 to $4,500. These are real numbers from our Las Vegas jobs in Paradise, Summerlin South, Anthem, and Spring Valley, not national averages from a website.
What moves the price: gate width and height, single vs. double leaf, slide vs. swing, the opener brand and horsepower, the distance from the electrical panel to the gate, and whether we’re setting new posts or reusing existing ones. HOA requirements in areas like Green Valley and Summerlin can also add a specific design language or finish requirement. To avoid overpaying, get a quote that separates materials and labor, and ask whether the control board and safety sensors are included. Our free estimate includes the full scope in writing: all materials, all labor, all programming, all cleanup. You won’t get a call three days later saying the concrete work “wasn’t in the original quote.”
Call (725) 777-5391 and we’ll set a time to walk the site and hand you a written price. No obligation, no deposit, no games.
Our Service Area Near Las Vegas
Portcullis Gate Repair Las Vegas covers the entire Las Vegas valley and the surrounding suburbs. We install gates in Las Vegas, Paradise, Summerlin South, Anthem, Green Valley, Winchester, Sunrise Manor, North Las Vegas, Aliante, Spring Valley, Whitney, and Nellis AFB. Typical response time for an estimate in the central valley is same day or next day, with most installs scheduled within one to two weeks depending on fabrication time. Every Portcullis location is independently owned and operated, but the Kingswell Guarantee is the same everywhere: written price, real arrival window, clean job site, and written guarantee on every job.
Serving Las Vegas, NV - Our Local Coverage Area
We’re based in the Las Vegas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Installation in Las Vegas
Gate installation is the complete process of building and mounting a gate at a driveway or entry point: measuring the opening, fabricating or ordering the panel, setting the posts, mounting the gate, installing the opener and safety sensors, and programming the controls. In Las Vegas, a full installation usually includes the electrical run from the house or panel to the gate location. We handle every step from first measurement to final walkthrough.
A basic gate opener installation on an existing gate can be done in four to six hours. A full custom gate installation with new posts, a fabricated panel, and an opener typically takes two to three days including concrete cure time. We’ll give you the timeline in writing with the estimate.
Gate installation in Las Vegas generally runs $3,200 to $7,500 for a complete automatic driveway gate, and $1,800 to $3,400 to add an opener to an existing gate. The range depends on gate type, size, opener brand, and the electrical work required. Call (725) 777-5391 for a free written estimate based on your actual site.
Yes. We install and service openers from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The technician arriving at your Las Vegas home already knows the specific quirks of your unit and carries the right diagnostic tools to talk to the control board.
We answer calls around the clock, and we’ll get a technician to your Las Vegas property as soon as possible if you’ve got a failed gate that can’t be secured. Full gate installations are scheduled work because they involve fabrication and concrete, but we can often install a temporary secure gate panel or secure the opening immediately, then complete the full installation on a scheduled date.
Every installation comes with the 365-Day Done Right Promise. That’s a written guarantee on the invoice: if anything we installed fails within 365 days, we return and fix it at no charge. The second visit doesn’t cost you a dime. Portcullis Gate Repair Las Vegas is a Kingswell company, and that guarantee is the same standard across every independently owned Kingswell location.
Clear the driveway and the area around the gate opening so we have working room and a clear path for the electrical run. Remove any vehicles from the driveway during the install window. If you live in an HOA, have your HOA’s design guidelines ready, especially in Summerlin, Green Valley, or Anthem. We’ll take care of the rest from first measurement to final cleanup.
Schedule Your Gate Installation Service in Las Vegas Today
If you need a gate installed in Las Vegas, call Portcullis Gate Repair Las Vegas at (725) 777-5391 for a free, written estimate. A live person answers 24/7, and Dean Prescott and the crew will walk the site, explain your options in plain English, and hand you a price in writing before any work begins. No obligation, no hard sell, no number that changes at the door.
Written by Dean Prescott, Owner at Portcullis Gate Repair Las Vegas, serving Las Vegas and the surrounding valley since 2008.