Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterWeld & Rust Repair in Las Vegas, NV
Weld and rust repair on a Las Vegas gate typically runs $150 to $650 depending on how far the corrosion has spread and whether a section needs to be cut out and replaced. Most jobs are done in a single visit, and we give you the written price before any metal gets touched. If your gate has a rust hole near a hinge, a cracked weld at a cross brace, or a sagging section that no longer lines up with the latch, this is the page that explains what we do and what it costs. Call us at (725) 777-5391 for a free estimate. You can also see our full Gate Repair in Las Vegas page for the broader scope of our work.
When You Need Weld & Rust Repair
Rust on a gate is not a cosmetic issue. Here in the Las Vegas Valley, the air is dry, but the soil under many gates is not. Irrigation overspray, pool water, and sprinkler runoff push moisture up against the bottom rail and hinge posts, and once the powder coat or paint is breached, the metal starts flaking. A gate that looks weathered on the surface may be losing structural mass at the hidden points where the bottom rail meets the hinge stile.
The practical answer is this: if you can see flaking metal, orange streaks, or a crack at a welded joint, the gate is telling you something. Here are the specific scenarios that bring Las Vegas homeowners to our Gate Repair services:
- Rust at the bottom rail or hinge side: This is the most common failure we see in Summerlin, Green Valley, and Henderson. The gate sits close to the ground or next to a stucco post, and sprinkler overspray sits against the steel. The metal swells, the gate drags, and the hinge eventually tears free.
- Cracked welds at cross braces or picket attachments: Las Vegas winds hammer gates. Over two or three summers, the repeated flexing causes welds to crack where a horizontal rail meets a vertical picket. The gate rattles, then starts to twist.
- A gate that suddenly sags or drags on one side: Usually the weld at the bottom hinge plate has failed. The panel hasn’t bent; the joint has let go. This needs a structural weld, not a hinge adjustment.
- Rust-through holes in the frame or pickets: If you can push a screwdriver through the metal, the section is too far gone for surface treatment. We cut out the bad section and weld in new steel, then treat the surrounding area to slow the return of the rust.
- Ornamental scrollwork that’s rusting from the inside out: Decorative steel with tight scrolls traps moisture. The rust hides inside the curves and only becomes visible when the metal starts flaking outward. We repair what’s salvageable and rebuild what isn’t.
- A gate that was painted over rust by a previous contractor: Paint over active rust lasts about one season in the Las Vegas sun. The rust keeps creeping under the coating, and the gate looks worse than it did before. We remove the loose material before any welding or coating work happens.
Our Weld & Rust Repair Process
We follow the same sequence on every weld and rust job, whether it’s a small 6-foot pedestrian gate in Aliante or a 20-foot custom driveway gate in The Ridges. The process is simple enough to understand but specific enough that you know what you’re paying for.
- Assessment and written quote: We inspect the gate in person, identify every rust-affected and weld-failed area, and give you a written price before any work begins. No “wait and see what we find” pricing. The number on the quote is the number on the invoice.
- Preparation and rust removal: We grind out the compromised metal, remove the rust scale back to clean steel, and cut out any section that’s too thin to weld. If a section of the frame needs replacing, this is where we measure and cut the new steel.
- Structural welding: Our tech welds the repaired joints and any replacement sections solid. For gates, we use MIG welding on steel and TIG where the material is thin or the joint is highly visible. The weld is ground smooth where it needs to be seamless, or left with a proper bead where the joint is structural and hidden.
- Rust neutralizer and primer: Before any paint or powder coat goes back on, the repaired area gets a rust converter or phosphoric acid treatment, then a zinc-rich primer. This is the step that door-slamming handymen skip, and it’s the step that determines whether the repair lasts three years or ten.
- Finish coat and color match: We match the existing color as closely as possible, whether you have a standard black powder-coated gate or a custom bronze finish. For small repairs we touch up the affected section; for larger jobs we may repaint the entire gate so the repair blends in.
- The 365-Day Done Right Promise: Every repair gets a written guarantee stamped on the invoice. If the weld cracks or the rust returns inside the guarantee period, we come back, redo the work, and you pay nothing for the return call. That promise is in writing, and it covers the full job, not just the parts.
Weld & Rust Repair Pricing in Las Vegas
We give honest ranges before you commit, so you know where the job will land. Every quote is in writing before any metal is touched. Here is How Much Does Gate Repair Cost? (2026 Price Guide) - Las Vegas, NV for weld and rust repair, based on the type of work:
- Small rust removal and touch-up on one area: $150 to $300. We grind, treat, prime, and paint a small affected section, usually around a weld point or hinge plate.
- Cracked weld repair on a rail or cross brace: $150 to $400. This includes grinding back to clean metal, welding the joint, and recoating the repaired area.
- Cut out and replace a rusted bottom rail section: $300 to $550. The bad steel comes out, new steel goes in, and we treat and finish the whole area. This includes the structural weld, not just a patch over the rust.
- Hinge-side frame repair and reinforcement: $250 to $650. When rust has eaten the bottom hinge mount, we cut out the section and weld in a reinforcement plate, then remount the hinge. This is one of the most common failures on older Las Vegas gates.
- Full gate rust remediation and repaint: $500 to $1,200 depending on gate size and condition. This involves removing active rust from the whole gate, welding any failing joints, priming, and repainting the full surface.
What affects cost the most? The extent of hidden rust once we open up an area. The thickness of the remaining steel. Whether we’re working around a gate operator or on a purely manual gate. And whether the gate’s finish is standard black or a custom color. We’ll explain all of this on the quote, not after the job is done. Call (725) 777-5391 and we’ll walk the gate with you in person.
FAQs – Weld & Rust Repair
Is rust repair worth it, or should I just replace the gate?
Rust repair is almost always worth it if the gate’s overall structure is still sound. A full replacement typically runs $2,500 to $8,000 in Las Vegas, while weld and rust repair on the same gate might cost $300 to $1,200. Unless the corrosion has compromised more than 40% of the metal, repair is the better financial decision. We’ll give you a straight answer on site, and we won’t sell a replacement if a repair will give you five more years.
How long does a rust repair last?
A properly done rust repair, with the affected area ground to clean steel, treated with rust converter, primed with zinc, and recoated, should last five to ten years in Las Vegas. If a gate has constantly wet soil at the base, we may recommend raising the bottom rail clearance or adjusting the sprinklers, because no coating will hold up against standing water. The 365-Day Done Right Promise covers the repair for the full year. Call (725) 777-5391 if you’d like an inspection.
Can you weld aluminum gates?
Yes, but aluminum is a different animal. Aluminum gates, which are common on newer Las Vegas homes, need TIG welding and a different surface treatment than steel. The repair process is similar to steel: grind the crack, weld, smooth, and recoat. The main difference is cost. Aluminum welding tends to run slightly higher per joint because the process is slower and the material is less forgiving.
Can you come out today if my gate’s weld has snapped?
We answer the phone with a live person 24/7, and we schedule emergency weld repairs for same-day or next-day service. A snapped weld usually means the gate won’t open or close properly, which affects security and, in some cases, blocks your driveway entirely. When you call, we’ll give you a real arrival window, not a four-hour “somebody will be there eventually” window. Call (725) 777-5391 and we’ll get a tech dispatched today.
Do you service BFT, Linear, or Viking gate openers affected by rust?
Yes. We have hands-on service experience with BFT, Linear, Viking, and Ghost Controls systems, among several other major brands. When a rust problem on the gate frame spreads into the operator mounting bracket or the actuator, we address both the metal repair and the Automatic Gate Repair alignment. The tech who arrives will know the specific system on your property, so you don’t pay for an hour of “figuring it out.”
Why Las Vegas Homeowners Call Portcullis for Weld & Rust Repair
Portcullis Gate Repair is an independently owned Kingswell company. What that means in plain words is this: we’re held to the four Kingswell Guarantee promises on every job, including yours. A written price before any work starts. A real arrival window that we actually hit. A clean job site when we leave. And a written guarantee stamped on every repair invoice. If the repair fails within 365 days, we come back and fix it at no charge. That’s the 365-Day Done Right Promise, and it’s not a marketing slogan. It’s written on the paperwork.
The Kingswell Way is the same standard across every Kingswell company: say the price before the work; show up in the window we gave; leave the place cleaner than we found it; put the guarantee in writing; come back if it fails. Every Portcullis location is independently owned and operated, but none of them can skip those promises. Not on a small weld. Not on a full rust remediation.
Our technicians arrive background-checked and in uniform. You’ll know exactly who is walking up your driveway and what they’re there to do. They carry the welding equipment, the steel stock, and the coating materials on the truck, which means most repair jobs are completed in a single visit.
We opened our doors in Las Vegas in 2008. Since then we’ve repaired rusted-out gates by the hundreds across the Valley, from the older ironwork in Paradise and Winchester to newer steel gates in Summerlin and Mountains Edge. We know what Las Vegas soil does to a gate. We know what the wind does to a cracked weld. And we know how to fix it so it stays fixed.
Call (725) 777-5391 for a free weld and rust repair estimate. You’ll get a real person on the line, a real price in writing, and a repair that carries a written guarantee. If you’re still exploring your options, start with our home page to see the full range of gate services we provide across the Las Vegas Valley.
Written by Dean Prescott, Owner at Portcullis Gate Repair Las Vegas, serving Las Vegas.